Aluminum Paint
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 433.00 | Volume Solids ±2% | 44.00 | Odor | Mixed aliphatic / aromatic |
| VOC lbs/G | 3.61 | Weight Solids ±2% | 55.00 | Thinning | Do not thin |
| |
| MPI # | 1 | Theor. Spread Rate | 480.0 | Weight | 8.00 |
| Gloss 60° | 95-105 | Wet Film Thickness | 3.2 | Viscosity | 59 - 64 Krebs Units |
| Sheen 85° | | Dry Film Thickness | 1.5 | Resistance | Very good |
| |
| Tinting Type | N/A | Toxic Properties | very low as a dry film | Cleanup | 799250x Mineral Thinner |
| Local Harvest | | Light Reflectance | 85 to 95% | Packaging | single & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees F. and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 1/2 to 1 hour | Dry To Sand | N/A | Tack Free | 1/2 -1 hour |
| Dry To Recoat | 12 hours | Dry To Topcoat | 12 hours | Dry To Hard | |
Prep & Prime
Surfaces must be clean, dry and free of contaminants such as wax, oils, grease, weld splatter, or loose mil/scale/rust. As a minimum, SSPC-SPC Hand Tool Cleaning or SSPC-SPC3 Machine Tool Cleaning is recommended. Smooth surfaces should be abraded to enhance adhesion. Improved performance can be achieved with SSPC-SP6 Commercial Blast. All surfaces prepared for painting should be coated within 8 hours of completion of surface prep.
| |
| |
| Masonry | Remove any loose material from surface. Prime bare areas with 501601x First Coat Primer |
| Metal | Clean and remove rust and mill scale. Prime with suitable metal primer, such as 7082XXX High Solids Barrier III Primer or 708195x All Purpose Metal Primer |
| |
| Wood | Recommend as primer for wood |
| |
Application
Do not apply when air surface temperatures are expected to drop below 50 degrees F. or rise above 95 degrees during application and drying.
| |
| |
| Brush | Use a natural bristle brush. |
| Roller / Pad | Ue 1/4" to 1/2" nap synthetic or lambswool roller cover. Use a synthetic pad. |
| Airless Spray | Recommended pressure 2000 to 2500 psi; using .013 to .016 tip orifice. |
| |
| Conventional Spray | Recommended air pressure 40-60 psi; fluid pressure 20 psi; JGA 510 gun, FX tip, 705 air cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 11/10/2011 - Please contact us at 800.452.2315 for additional information or questions
