Cat-A-Lac Lacquer
Product Data Sheet
| | | |
| Description | AN INTERIOR CLEAR PRE-CATALYZED WOOD LACQUER |
756400x Gloss
746400x Semi Gloss
726400x Satin | Approved by the Master Painter Institute under category #85, 86 & 87,122,123 & 124. Cat-A-Lac lacquers meet or exceed the test requirements of the National Kitchen Cabinet Assoc., ANSI test A161.1 |
|
| Basic Use | Cat-A-Lac is an internally acid catalyzed chemical resistant wood finish that eliminates the need to mix expensive, limited potlife, two component lacquers. Exhibits excellent resistance to impact, acid, alkali and solvent. A premium quality, clear wood finish for fine quality kitchen cabinets, doors, millwork or other interior wood surfaces. Cat-A-Lac develops good film build and depth as well as excellent resistance to household detergents, household chemicals, cold checking, marring and abrasion. |
| |
| | | |
| | | |
| | | |
Properties
| | | | | |
| VOC gr/L | 675.00 | Volume Solids ±2% | 18.00 | Odor | lacquer thinner |
| VOC lbs/G | 5.63 | Weight Solids ±2% | 24.00 | Thinning | do not thin |
| |
| MPI # | 85-6-7,122-3-4 | Theor. Spread Rate | 350.0 | Weight | 7.50 |
| Gloss 60° | 80-90 | Wet Film Thickness | | Viscosity | 30 - 35 second Zahn #2 |
| Sheen 85° | | Dry Film Thickness | | Resistance | moisture is excellent |
| |
| Tinting Type | Industrial | Toxic Properties | Use with adequate ventilation. | Cleanup | 799461x Lacquer Thinner |
| Local Harvest | | Light Reflectance | | Packaging | single & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 10 minutes | Dry To Sand | 30 minutes | Tack Free | 10 minutes |
| Dry To Recoat | 30 minutes: Must be sanded p | Dry To Topcoat | 30 minutes | Dry To Hard | N/A |
Prep & Prime
Surfaces to be coated must be free of dirt, oil, mildew, excessive chalk and other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces, and then scuff sand using 80 to 100 grit sandpaper on a hand sander. remove all sanding dust.
| |
| |
| |
| Metal | Not recommended for these surfaces |
| |
| Wood | Wood surfaces should be free of foreign matter and properly sanded. Cat-A-Lac may be used as a self-seal system. Dry and sand as a conventional sealer. Do not use a stearated sealer under Cat-A-Lac. |
| |
Application
Surface temperatures should be above 50 degrees Fahrenheit. Where humid conditions exist, blushing may occur. Use 799464 Lacquer Retarder when these conditions exist. This is a high build sealer and contains sanding aids; thus, it cannot be sprayed hot.
| |
| |
| |
| |
| Airless Spray | Use equipment capable of constant 1800 psi at tip. An .012" to .018" tip is recommended. |
| HVLP | DeVilbiss JGHV 531 MP or equivalent. |
| Conventional Spray | Binks Slimline Mach 1 or equivalent gun. 92 Air Cap with 92 nozzle. Use double regulated air pot with 5 - 7 psi air pressure at gun. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 6/2/2011 - Please contact us at 800.452.2315 for additional information or questions
