Barrier III High Solids Primer
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 398.00 | Volume Solids ±2% | 53.00 | Odor | dominant of aromatic paint |
| VOC lbs/G | 3.32 | Weight Solids ±2% | 70.00 | Thinning | none recommended |
| |
| MPI # | 79 & 95 | Theor. Spread Rate | 425.0 | Weight | 11.20 |
| Gloss 60° | 0-20 | Wet Film Thickness | 4 mils | Viscosity | 70 - 75 Krebs Units |
| Sheen 85° | | Dry Film Thickness | 2.0 mils | Resistance | excellent |
| |
| Tinting Type | | Toxic Properties | Non-toxic as dry film | Cleanup | 799260x Synthetic Reducer |
| Local Harvest | | Light Reflectance | Less than 25% | Packaging | five gallons |
| |
| | | | | |
| |
| Hap Content | 0.16 lbs/gal-19.2 gr/ltr | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
Dry time will vary depending upon film thickness, temperatures, humidity, etc. Allowing overnight dry will give fastest system adhesion when topcoated.
| | | | | |
| Dry To Touch | 25 to 45 min. | Dry To Sand | N/A | Tack Free | 25 to 45 min |
| Dry To Recoat | 3-6 hours | Dry To Topcoat | 3 to 6 hours | Dry To Hard | N/A |
Prep & Prime
Surfaces must be clean, dry, and free of contaminants such as wax, oils, grease, weld splatter, loose mil, scale, rust. As a minimum SSPC-SPC Hand Tool Cleaning or SSPC-SPC3 Machine Tool Cleaning is recommended for interior exposure. Smooth surfaces should be abraded to enhance adhesion. Improved performance can be achieved with and SSPC-SPC6 Commercial Blast. All surfaces prepared for painting should be coated within 8 hours of completion of surface prep.
| |
| |
| Masonry | Check with coatings representative. |
| Metal | Surfaces to be primed must be thoroughly cleaned of all foreign material by sandblasting, wire brushing, wheel abrading, etc. All grease, cutting oil, etc. must be removed prior to priming. For best results, prime metal immediately after cleaning. |
| |
| Wood | Check with coatings representative. |
| |
Application
Spray application recommended. may be brushed or rolled.
CONDITIONS: Do not apply when surface temps are expected to drop below 40 degrees F. or rise above 95 degrees F. during application and drying. Surface temperature must be least 50 degrees F. above dew point. Do not appy to surfaces which will be exposed to rain or moisture before coating is dry.
| |
| Coats | One or more depending on desired dry film thickness. |
| Brush | A top quality natural bristle brush is recommended. |
| Roller / Pad | Use 3/16" to 3/8" nap synthetic or lambswool roller cover. use a synthetic pad. |
| Airless Spray | Recommend pressure 2000 to 2500 psi; using .013 to .016 tip orifice. |
| HVLP | .055 - .70 nozzle, 8 - 10 psi air cap atomizing air. |
| Conventional Spray | Recommended air pressure 40 - 60 psi; fluid pressure 20 psi; JGA 510 gun, FX tip, 705 air cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 11/15/2011 - Please contact us at 800.452.2315 for additional information or questions
