Barrier III - Rust Inhibitive Primer
Product Data Sheet
| | | |
| Description | An easily Applied, Multi-Purpose, Fast Dry, Lacquer Resistant, Phenolic Modified Alkyd Primer. |
708001x White
708095x Red Oxide
708098x Gray
708099x Black | |
|
| Basic Use | THIS PRODUCT FOR INDUSTRIAL USE ONLY. An easily applied, multi-purpose, fast dry, lacquer resistant, phenolic modified alkyd primer. It is a valuable "lead and chromate free" maintenance primer because of its ability to replace a multitude of primers usually required to insure compatibility with various topcoats. This primer can be used over most old, well oxidized coatings without wrinkling or lifting; thereby, allowing for the possibility of upgrading present surfaces to a more chemical resistant system. It has good weathering characteristics to protect metal in storage, transit or during erection. Barrier II may be topcoated with a variety of finish coats such as, alkyds, epoxies, most coal tars, chlorinated rubber and emulsions.
It has good weathering characteristics to protect metal in storage, transit or during erection. |
| |
| | | |
| | | |
| | Mixing Instructions | Stir thoroughly. |
Properties
| | | | | |
| VOC gr/L | 543.00 | Volume Solids ±2% | 37.00 | Odor | dominant aromatic odor |
| VOC lbs/G | 4.53 | Weight Solids ±2% | 57.00 | Thinning | 799260x Synthetic Reducer |
| |
| MPI # | | Theor. Spread Rate | 380.0 | Weight | 10.60 |
| Gloss 60° | 0-15 | Wet Film Thickness | 4 mils | Viscosity | 70 - 75 Krebs Units |
| Sheen 85° | N/A | Dry Film Thickness | 1.5 mils | Resistance | Excellent |
| |
| Tinting Type | Industrial | Toxic Properties | Non-toxic as dry film | Cleanup | 799260x Synthetic Reducer |
| Local Harvest | | Light Reflectance | white 85%, lower on tints | Packaging | single & five gallons |
| |
| | | | Flash Point | 60º |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 10 to 20 minutes | Dry To Sand | 1 hour | Tack Free | 10 to 20 minutes |
| Dry To Recoat | 1 hour | Dry To Topcoat | 1 hour | Dry To Hard | 1 hour |
Prep & Prime
Surfaces must be clean, dry and free of contaminants such as wax, oils, grease, weld splatter, or loose mil/scale/rust. As a minimum, SSPC-SPC Hand Tool Cleaning or SSPC-SPC3 Machine Tool Cleaning is recommended. Smooth surfaces shouldbe abraded to enhance adhesion. Improved performance can be achieved with SSPC-SP6 Commercial Blast. All surfaces prepared for painting should be coated within 8 hours of completion of surface prep.
| |
| |
| Masonry | Not recommended for these surfaces, but may be used satisfactorily over previously coated surfaces. Bare areas must be primed with 501601x First Coat Primer. |
| Metal | Galvanized: Clean thoroughly. Prime with 74079x Galva Cling.
Ferrous: Can be applied directly to clean, dry, ferrous metal. |
| |
| Wood | Not recommended for these surfaces, but may be used satisfactorily over previously coated surfaces. Bare areas must be primed with 501601x First Coat Primer |
| |
Application
Spray application recommended. may be brushed or rolled.
CONDITIONS: Do not apply when surface temp are expected to drop below 50 degrees F. or rise above 95 degrees F. during application and drying. Surface temperature must be least 5 degrees F. (3 C) above dew point. Do not apply to surfaces which will be exposed to rain or moisture before coating is dry.
| |
| Coats | One or more depending on desired dry film thickness. |
| Brush | Not recommended. |
| Roller / Pad | Not recommended. |
| Airless Spray | Recommend pressure 2000 to 2500 psi, using .013 to .016 tip orifice. |
| |
| Conventional Spray | Recommend air pressure 40 - 60 psi; fluid pressure 20 psi; JGA 510 gun, FX tip, 705 air cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 8/1/2011 - Please contact us at 800.452.2315 for additional information or questions
