*NEW* Metal Master DTM - Gloss
Product Data Sheet
| | | |
| Description | AN INT/EXT PIGMENTED ACRYLIC HYBRID WATERBOURNE HIGH GLOSS DIRECT TO METAL (DTM) INDUSTRIAL MAINTENANCE COATING |
558901x White Base
558902x Midtone Base
558903x Deeptone Base
558904x Neutral Base | Adhesion (ASTMD3359) Steel 5, Aluminum 5, Galvanized 4
Hardness (ASTMD2134) 12, (ASTMD3363) F
Salt Fog (ASTMB117) 500 hrs (astmd610) Rust 9 (astmd714) BListering 10 |
|
| Basic Use | For general purpose maintenance on tank exteriors, transmission towers, microware towers, metal buildings, structural steel and other metal, and masonry surfaces. Metal Master DTM is flash rust resistant on properly prepared surfaces. |
| Colors | white to black |
| | Components | Acrylic Hybrid Technology |
| Shelf Life | 3 years | | |
| | | |
Properties
| | | | | |
| VOC gr/L | 109.00 | Volume Solids ±2% | 35.00 | Odor | dominant of latex paint |
| VOC lbs/G | 0.91 | Weight Solids ±2% | 47.00 | Thinning | none recommended |
| |
| MPI # | | Theor. Spread Rate | 220.0 | Weight | 10.10 |
| Gloss 60° | 90+ | Wet Film Thickness | 6.5 - 10 mils | Viscosity | 90 - 100 Krebs Units |
| Sheen 85° | | Dry Film Thickness | 2.5 - 4 mils | Resistance | excellent |
| |
| Tinting Type | | Toxic Properties | Non-toxic as dry film | Cleanup | warm soapy water |
| Local Harvest | 15.6% | Light Reflectance | white 90%, lower on tints | Packaging | single & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 3 hours | Dry To Sand | | Tack Free | |
| Dry To Recoat | 6 - 8 hours | Dry To Topcoat | | Dry To Hard | 7 days |
Prep & Prime
Surfaces must be clean, dry and free of contaminants such as wax, oils, grease, weld splatter, or loose mil/scale/rust. As a minimum, SSPC-SPC Hand Tool Cleaning or SSPC-SPC3 Machine Tool Cleaning is recommended. Smooth surfaces should be abraded to enhance adhesion. Improved performance can be achieved with SSPC-SP6 Commercial Blast. All surfaces prepared for painting should be coated within 8 hours of completion of surface prep.
| |
| |
| Masonry | Must be thoroughly cured before painting. Priming with 501601x First Coat Primer is recommended prior to topcoating. |
| Metal | Must be thoroughly cleaned before painting. Remove chalk and old paint not tightly bonded to the surface. Clean all visible rust to bare metal. Smooth or shiny surfaces should be abraded to improve adhesion of the coating to the substrate. |
| |
| Wood | Not recommended |
| |
Application
Do not apply when air or surface temperatures are expected to drop below 50 degrees or rise above 95 degrees Fahrenheit during application and drying.
| |
| |
| Brush | Use a top quality nylon/polyester brush . |
| Roller / Pad | Use a top quality synthetic roller cover. |
| Airless Spray | Equipment capable of maintaining constant 1800 psi at the tip. Use a .013" to .019" tip orifice. |
| |
| Conventional Spray | DeVilbiss JGA Gun or equivalent. Fluid pressure 25 - 30 psi; pressure 40 - 50 psi. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 11/10/2011 - Please contact us at 800.452.2315 for additional information or questions
