Multi Master DTM - Semi Gloss
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 140.00 | Volume Solids ±2% | 36.00 | Odor | dominant of latex paint |
| VOC lbs/G | 1.17 | Weight Solids ±2% | 47.00 | Thinning | none recommended |
| |
| MPI # | | Theor. Spread Rate | 200.0 | Weight | 10.32 |
| Gloss 60° | 40-50 | Wet Film Thickness | 8.25 mils | Viscosity | 95 - 100 Krebs Units |
| Sheen 85° | 80+ | Dry Film Thickness | 3.25 mils | Resistance | excellent |
| |
| Tinting Type | universal | Toxic Properties | Non-toxic as dry film | Cleanup | warm soapy water |
| Local Harvest | 12.6% | Light Reflectance | white 90%, lower on tints | Packaging | single & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 1 1/2 hour | Dry To Sand | N/A | Tack Free | 1/2 to 1 hour |
| Dry To Recoat | 4 hours | Dry To Topcoat | 4 hours | Dry To Hard | 7-14 days |
Prep & Prime
*All substrates must be clean & dry prior to application* Remove dirt, dust, oil & all other contaminants that could interfere with adhesion of the coating per SSPC SP1. Glossy, glazed, or shiny surfaces should be abraded using SSPC-SP2 or SP3 methods for moderate environments. For maximum performance, a sweep blast cleaning to a SSPC-SP7 Brush-Off Blast Standard is recommended to improve service life of the coating.
When priming factory finished siding such as Kynar, fluorocarbon, or baked polyester polymers the adhesion must be confirmed using test patches. Allow test patches one week of dry time before testing adhesion to ensure proper cure. Confirm using ASTM 3359 Method A X-Cut Tape Test method with results of 4A to 5A prior to proceeding with application. Contact your Rodda Paint representative with any questions.
| |
| Concrete Block | Apply 501901x Sprayable Block Filler and allow to thoroughly dry before topcoating. |
| Masonry | Must be thoroughly cured before painting. Priming with 501601x First Coat Primer is recommended prior to topcoating. |
| Metal | Suggest minimum preparation of Hand Tool Cleaning per SSPC-SP2. Remove all grease & oil per Solvent Cleaning SSPC-SP1. Remove chalk & old paint not tightly bonded to the surface. Clean all visible rust to bare metal. Smooth or shiny surfaces should be abraded to improve adhesion of the coating to the substrate. |
| |
| Wood | Priming with 501601x First Coat Primer is recommended prior to topcoating. |
| |
Application
Apply when substrate temperature is 50 degrees F. or above and expected to remain above 50 degrees F. for a minimum of 24 hours. Do not apply out doors if rain or dew is expected within 24 hours of completion.
| |
| Coats | Apply one or two coats to achieve 3.0 - 4.0 mil dry film thickness |
| Brush | Use a top quality nylon/polyester brush |
| |
| Airless Spray | Equipment capable of maintaining constant 1800 psi at the tip (.013" to .019" tip orifice) |
| |
| Conventional Spray | DeVilbiss JGA Gun or equivalent. Fluid pressure 25 - 30 psi (pressure 40 - 50 psi) |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 1/20/2012 - Please contact us at 800.452.2315 for additional information or questions
