AC Extreme Satin
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 102.00 | Volume Solids ±2% | 42.00 | Odor | Slight ammonia odor. |
| VOC lbs/G | 0.85 | Weight Solids ±2% | 58.00 | Thinning | As necessary with water or 591 |
| |
| MPI # | | Theor. Spread Rate | 390.0 | Weight | 11.40 |
| Gloss 60° | 8-12 | Wet Film Thickness | 3.5 - 4.2 | Viscosity | 102 to 104 Krebs Units |
| Sheen 85° | | Dry Film Thickness | 1.5 to 2mils | Resistance | Very good |
| |
| Tinting Type | Universal | Toxic Properties | Non-toxic as a dry film. | Cleanup | Clean with hot soapy water |
| Local Harvest | | Light Reflectance | 90% on white, lower on colors | Packaging | Stocked in single and five gal |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 4 hours @ 35-45 degrees F | Dry To Sand | N/A | Tack Free | 4 hours |
| Dry To Recoat | 24 hours @ 35-45 degrees F | Dry To Topcoat | 24 hours | Dry To Hard | N/A |
Prep & Prime
Surfaces to be coated must be free of dirt, oil, mildew, excessive chalk and other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces, and then scuff sand using 80 to 100 grit sandpaper on a hand sander. Remove all sanding dust.
| |
| Concrete Block | Above 50 F: Fill with 501901x Sprayable Smooth Block Filler. |
| Masonry | Above 50 F: Rodda Surf Bond II |
| Metal | Not designed for metal, but performs quite satisfactory on properly primed ferrous and clean galvanized metal, such as gutters and downspouts. |
| |
| Wood | Above 50 F: First Coat Latex Primer (blocks tannin bleed). Below 50 F: Multi-Prime Latex Primer (does not block tannin bleed). |
| |
Application
Before painting, make sure air, surface, and paint temperature are above 35 degrees Fahrenheit. Do not paint if rain or snow or freezing temperatures are expected within 24 hours. Do not apply if temperature is above 95 degrees.
| |
| |
| Brush | A nylon/polyester brush is recommended for this project. |
| Roller / Pad | Use 3/8" to 1" nap synthetic roller cover.-Use a synthetic pad. |
| Airless Spray | Recommend pressure 2000 to 2500 psi, using .015 to .21 tip. |
| HVLP | Reduce up to one pint per gallon with water. Accuspray 24K |
| Conventional Spray | Reduce up to one pint per gallon with water. Recommended air pressure 40-60 psi; fluid pressure 20 psi; tip size .0042" to .0045" with matching cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 6/28/2011 - Please contact us at 800.452.2315 for additional information or questions
