AC-909 Satin
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 89.00 | Volume Solids ±2% | 36.00 | Odor | Slight ammonia |
| VOC lbs/G | 0.74 | Weight Solids ±2% | 50.40 | Thinning | None Recommended |
| |
| MPI # | G3 | Theor. Spread Rate | 374.0 | Weight | 10.72 |
| Gloss 60° | 8.5-12.5 | Wet Film Thickness | 4 mils | Viscosity | 100 - 105 Krebs Units |
| Sheen 85° | 15-20 | Dry Film Thickness | 1.5 mils | Resistance | Contains film preservatives |
| |
| Tinting Type | universal | Toxic Properties | Non-toxic as dry film | Cleanup | hot soapy water |
| Local Harvest | 25-34 | Light Reflectance | white 90%, less on tints | Packaging | one & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 1 1/2 hours | Dry To Sand | N/A | Tack Free | 1 1/2 hours |
| Dry To Recoat | 3 hours | Dry To Topcoat | N/A | Dry To Hard | 3-6 hours |
Prep & Prime
Surfaces to be coated must be free of dirt, oil, mildew, excessive chalk and other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces and then scuff sand using 80 to 100 grit sandpaper on a hand sander. Remove all sanding dust. Do not apply over unprimed metal.
New cementitious substrates may have high pH levels and should be tested before coating. If pH is above 8, prime with Rodda's First Coat primer.
| |
| Concrete Block | New Interior and Exterior: Should be filled with No. 501901x Sprayable Block Filler prior to painting for optimum moisture resistance. |
| Masonry | Prime with 501801x Surfbond II, Rodda Paint's First Coat primer or 512301x pHlex-tite . Should be well cured and thoroughly clean before painting. |
| Metal | Prime with 508901x Metal Master Primer. |
| |
| Wood | New wood should be primed with Rodda's 501601x First Coat prior to AC-909 finish coat. Surfaces to be repainted should be thoroughly clean prior to painting. |
| |
Application
Avoid application to surfaces exposed and heated from direct sunlight. Before painting, make sure air, surface and paint temperature are above 35º F. Do not paint if rain, snow or freezing temperatures are expected within 24 hours. Avoid application to surfaces exposed and heated from direct sunlight.
| |
| |
| Brush | A nylon/polyester brush is recommended for this project. |
| Roller / Pad | Use 3/8" to 3/4" nap synthetic roller cover.-Use a synthetic pad. |
| Airless Spray | Recommend pressure 2000 to 2500 psi, using .015 to .21 tip orifice. |
| HVLP | Reduce up to one pint per gallon with water. Accuspray 24K |
| Conventional Spray | Reduce up to one pint per gallon with water. Recommended air pressure 40-60 psi; fluid pressure 20 psi; tip size .0042" to .0045" with matching cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 11/21/2011 - Please contact us at 800.452.2315 for additional information or questions
