pHlex-tite
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 48.00 | Volume Solids ±2% | 46.00 | Odor | slight ammonia |
| VOC lbs/G | 0.40 | Weight Solids ±2% | 60.00 | Thinning | none recommended |
| |
| MPI # | 3, 10 & 113 | Theor. Spread Rate | 98.0 | Weight | 11.10 |
| Gloss 60° | 5.0 | Wet Film Thickness | 16 mils, elastomeric finish | Viscosity | 120 - 130 Krebs Unit |
| Sheen 85° | 5.0 | Dry Film Thickness | 7.5 mils, elastomeric finish | Resistance | Excellent |
| |
| Tinting Type | universal | Toxic Properties | Non-toxic as dried film | Cleanup | warm soapy water |
| Local Harvest | | Light Reflectance | | Packaging | one & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| Elongation | 1 coat @ 8.5 dry mils, 14 day cure @ 75 degrees: 250% |
| |
| |
| |
| Tensile Strength | 1 coat @ 8.5 dry mils, 14 day cure @ 75 degrees: 280 psi |
| |
| Wind Driven Rain | 2 coats pHlextite @ 7.0 dry mils per coat, passes ASTM D6940 |
| |
| Alkali Resistance | ASTM D1308, passes |
Dry Times
At 77 Fahrenheit and 50% relative humidity
| | | | | |
| Dry To Touch | 3 - 4 hours | Dry To Sand | N/A | Tack Free | 3-4 hours |
| Dry To Recoat | 24 hours | Dry To Topcoat | 24 hours | Dry To Hard | N/A |
Prep & Prime
Surface must be free of dirt, oil, mildew, excessive chalk and other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces, and then scuff sand using 80 to 100 grit sandpaper on a hand sander. Remove all sanding dust.
For primer application use 3.5-4.5 wet mils (1.5-2.0 dry mils)
| |
| |
| Masonry | Pressure clean to remove all dirt, dust, grease, oil, loose material, chalk, loose checked or peeling paint, form release agents, etc. Remove all mildew and allow surface to dry thoroughly. Concrete must be cured minimum 7 days. |
| |
| |
| |
| |
Application
Apply at temperatures between 35F and 95 F. For proper elongation and alkali resistance pHlex-tite must be applied at 14 - 18 mils wet, 6.5 - 8.5 mils dry.
| |
| Coats | 1 coat at 14 - 18 wet mils for elastomeric properties; primer application 3.5-4.5 wet mils |
| Brush | Use a top quality nylon/polyester brush |
| Roller / Pad | Use a top quality synthetic roller with 3/4" to 1 1/2" nap |
| Airless Spray | Use equipment capable of constant 2300 psi, using a .21" to .30" tip size. |
| |
| |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 10/13/2011 - Please contact us at 800.452.2315 for additional information or questions
