Super Roflex Elastomeric
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 82.00 | Volume Solids ±2% | 51.00 | Odor | mild ammonia |
| VOC lbs/G | 0.68 | Weight Solids ±2% | 63.00 | Thinning | not recommended |
| |
| MPI # | 42 & 113 | Theor. Spread Rate | 55.0 | Weight | 11.20 |
| Gloss 60° | 1-5 | Wet Film Thickness | 15 mils per coat | Viscosity | 104 - 112 Krebs Units |
| Sheen 85° | | Dry Film Thickness | 7.5 mils per coat | Resistance | Excellent. w/o ponding water |
| |
| Tinting Type | universal | Toxic Properties | Non-toxic as dry film | Cleanup | hot soapy water |
| Local Harvest | 15-17% | Light Reflectance | white 88%, less on tints. | Packaging | single & five gallons |
| |
| pH | 8.2 to 8.8 | Pigment Solids | 35 .1% | Flash Point | N/A |
| |
| | Pigment Volume | 31 ± 2% | H2O Vapor | At 18 mils DFT = 8 perms |
| |
| Elongation | 505%-246% |
| |
| Crack Bridging | 108 mils - width of crack at break-55 mils - width at crack break |
| |
| Tensile Strength | 249 psi (ASTM D 412)-390 psi (ASTM D 412) |
| |
| Wind Driven Rain | Passes (TTC-555B) |
| |
| Alkali Resistance | Excellent |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity:
| | | | | |
| Dry To Touch | 3 hours | Dry To Sand | N/A | Tack Free | 3 hours |
| Dry To Recoat | 16 hours | Dry To Topcoat | 16 hours | Dry To Hard | N/A |
Prep & Prime
Surfaces to be coated must be free of dirt, oil, mildew, excessive chalk and other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces, and then scuff sand using 80 to 100 grit sandpaper on a hand sander. Remove all sanding dust.
| |
| Concrete Block | Fill 501901x Sprayable Block Filler. |
| Masonry | Should be well cured and thoroughly clean before painting. Surface must be free of dirt, grease, efflorescence, form treatments, curing compounds, and laitance. Prime with 501801x Surfbond II Surface Conditioner. |
| Metal | Not designed for metal, but performs quite satisfactorily on properly primed ferrous metal and clean galvanized metal, such as gutters and down spouts. |
| |
| Wood | New wood should be primed with Rodda Paint's First Coat primer. Surfaces to be repainted should be thoroughly clean prior to painting. |
| |
Application
Avoid application to surfaces exposed and heated from direct sunlight.Before painting, make sure air, surface and paint temperature are above 40 degrees F. Do not paint if rain, snow or freezing temperatures are expected within 24 hours. Avoid application to surfaces exposed and heated from direct sunlight.
| |
| |
| |
| |
| Airless Spray | Use equipment capable of constant 2000 psi, using a .21" to .30" tip size. |
| |
| |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 6/3/2011 - Please contact us at 800.452.2315 for additional information or questions
