AC-911 Hi Hide Velvet Flat
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 68.00 | Volume Solids ±2% | 44.00 | Odor | Slight ammonia |
| VOC lbs/G | 0.57 | Weight Solids ±2% | 61.00 | Thinning | None Recommended |
| |
| MPI # | | Theor. Spread Rate | 471.0 | Weight | 12.00 |
| Gloss 60° | 0-5 | Wet Film Thickness | 3 mils | Viscosity | 99 - 103 Krebs Units |
| Sheen 85° | | Dry Film Thickness | 1.5 mils | Resistance | very good |
| |
| Tinting Type | universal | Toxic Properties | Non-toxic as dry film | Cleanup | hot soapy water |
| Local Harvest | | Light Reflectance | Depends on color | Packaging | single & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
At 77 degrees Fahrenheit and 50% Relative Humidity.
| | | | | |
| Dry To Touch | 1 1/2 hours | Dry To Sand | N/A | Tack Free | 1-1/2 hours |
| Dry To Recoat | 3 hours | Dry To Topcoat | 3 hours | Dry To Hard | N/A |
Prep & Prime
Surfaces to be coated must be free of dirt, oil, mildew, excessive chalk an other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces, and then scuff sand using 80 to 100 grit sandpaper on a hand sander. Remove all sanding dust.
| |
| Concrete Block | New Interior and Exterior: Should be filled with 501901x Sprayable Block Filler prior to painting for optimum moisture resistance. |
| Masonry | Prime with 501801x Surfbond II or 501601x First Coat Primer. Surfaces to be repainted should be will cured and thoroughly clean before painting. |
| Metal | Not designed for metal, but performs quite satisfactorily on properly primed ferrous metal and clean galvanized metal, such as gutters and down spouts. |
| |
| Wood | New wood should be primed with 501601x First Coat prior to finish coat. Surfaces to be repainted should be thoroughly clean prior to painting. |
| |
Application
Do not apply to surfaces below 50 degrees Fahrenheit. Avoid application to surfaces exposed and heated from direct sunlight.
| |
| |
| Brush | A nylon/polyester brush is recommended for this project. |
| Roller / Pad | Use 3/8" to 3/4" nap synthetic roller cover.-Use a synthetic pad. |
| Airless Spray | Recommend pressure 2000 to 2500 psi, using .015 to .21 tip. |
| HVLP | Reduce up to one pint per gallon with water. Accuspray 24K |
| Conventional Spray | Reduce up to one pint per gallon with water. Recommended air pressure 40-60 psi; fluid pressure 20 psi; tip size .0042" to .0045" with matching cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 6/28/2011 - Please contact us at 800.452.2315 for additional information or questions
