Galva-Cling
Product Data Sheet
| | | |
| Description | A PIGMENTED ACRYLIC BONDING METAL PRIMER |
| 74079x Off White | *Lead Free* Film dried overnight conforms to ASTM D3359 Lattic Adhesion test. |
|
| Basic Use | A valuable coating for application as primer or finish to bond firmly to Galvanized Metal, Tin, or Similar Non-Porous Surfaces. Ideal for application on roofs, gutters, piping, ducts, flashings, machinery, fences or buildings. Galva Cling also has shown to perform well on fiberglass, ceramic tile, porcelain, glass, etc. A patch test is required to check products adhesion on specific substrates. |
| |
| | | |
| | | |
| | | |
Properties
| | | | | |
| VOC gr/L | 633.00 | Volume Solids ±2% | 27.80 | Odor | Characteristic of Lacquer |
| VOC lbs/G | 5.28 | Weight Solids ±2% | 49.50 | Thinning | none recommended |
| |
| MPI # | | Theor. Spread Rate | 257.0 | Weight | 10.50 |
| Gloss 60° | .1-10 | Wet Film Thickness | 6 | Viscosity | 30-40 Zahn 2 |
| Sheen 85° | | Dry Film Thickness | 1.75 | Resistance | |
| |
| Tinting Type | Industrial | Toxic Properties | | Cleanup | 799260x Synthetic Reducer |
| Local Harvest | | Light Reflectance | | Packaging | single & five gallons |
| |
| | | | Flash Point | 23 degrees F |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
| | | | | |
| Dry To Touch | 10-15 min | Dry To Sand | 1 hour | Tack Free | 10 to 15 minutes |
| Dry To Recoat | 1 hour | Dry To Topcoat | 1 hour | Dry To Hard | 1 hour |
Prep & Prime
Surfaces must be clean, dry and free of contaminants such as wax, oils, grease, weld splatter, or loose mil/scale/rust. As a minimum, SSPC-SPC Hand Tool Cleaning or SSPC-SPC3 Machine Tool Cleaning is recommended. Smooth surfaces should be abraded to enhance adhesion. Improves performance can be achieved with SSPC-SP6 Commercial Blast. All surfaces prepared for painting should be coated within 8 hours of completion of surface prep.
Application
Do not apply when air or surface temperatures are expected to drop below 50 degrees F. or rise above 95 degrees F. during application and drying.
| |
| |
| Brush | Use a natural bristle |
| Roller / Pad | Use a 1/4" nap |
| Airless Spray | Use equipment capable of constant 2000 psi, with a .015 to .017 tip size |
| |
| Conventional Spray | Suggest a dual regulated pressure pot with a Devilbiss JGA gun, 704 FX nozzle, 40-60 psi air pressure & 20 psi fluid pressure (or equivalent system) |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 6/3/2011 - Please contact us at 800.452.2315 for additional information or questions
