WoodMaster Low-Gloss
Product Data Sheet
Properties
| | | | | |
| VOC gr/L | 195.00 | Volume Solids ±2% | 36.00 | Odor | mild ammonia |
| VOC lbs/G | 1.63 | Weight Solids ±2% | 48.00 | Thinning | use 913 |
| |
| MPI # | | Theor. Spread Rate | 374.0 | Weight | 10.60 |
| Gloss 60° | 25-35 | Wet Film Thickness | 4 mils | Viscosity | 98 - 100 Krebs Units |
| Sheen 85° | 65-75 | Dry Film Thickness | 1.5 mils | Resistance | Excellent |
| |
| Tinting Type | universal | Toxic Properties | Non-toxic as dried film | Cleanup | warm soapy water |
| Local Harvest | 17% | Light Reflectance | | Packaging | one & five gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
| | | | | |
| Dry To Touch | 1/2 hour. | Dry To Sand | | Tack Free | |
| Dry To Recoat | 2 hours. | Dry To Topcoat | | Dry To Hard | |
Prep & Prime
Surfaces to be coated must be free of dirt, oil, mildew, excessive chalk and other foreign matter. Remove loose paint and patch holes or cracks. Prime bare surfaces, dull or prime glossy surfaces, and then scuff sand using 80 to 100 grit sandpaper on a hand sander. remove all sanding dust.
| |
| Concrete Block | Fill with 501901x Sprayable Block Filler. |
| Masonry | Primer with 505901x Multi Prime or 501601x First Coat Primer. |
| Metal | Galvanized & Aluminum: Surfaces must be properly treated. Ferrous Metal: Prime with 7082xxx Barrier II High Solids Metal Primer or 708195x All Purpose Rust Primer. |
| Wallboard | Prime with 507801x Scotseal. |
| Wood | New Interior: Prime with 502001x Unique II Acrylic Enamel Undercoater.
New Exterior: prime with 501601x First Coat Primer
Do not use as a top-coat over Lacquer Primer Surfacer. |
| |
Application
Do not apply when air or surface temperatures are expected to drop below 50 degrees F. or rise above 95 degrees F. during application and drying.
Spray or roller application is preferred. Roller application will result in a very pleasing, slight stipple effect.
| |
| |
| Brush | A nylon/polyester brush is recommended for this product. |
| Roller / Pad | Use a 3/8" to 1/2" nap synthetic roller cover.-Use a synthetic pad. |
| Airless Spray | Recommended pressure 2000 to 2500 psi using .015" to .021" tip orifice. |
| HVLP | Reduce up to one pint with watere per gallon. Accuspray 24K. |
| Conventional Spray | Reduce up to one pint per gallon with water. Recommended air pressure 40-60 psi; fluid pressure 20 psi; tip size .0042" - .0045: matching cap. |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 5/19/2011 - Please contact us at 800.452.2315 for additional information or questions
