Clear Satin WB Acrylic Finish
Product Data Sheet
| | | |
| Description | Aqueous Acrylic Latex. An Interior/Exteiror, single component, waterborne 100% acrylic latex DTM all purpose paint. |
| |
|
| Basic Use | |
| Colors | Clear |
| | | |
| | Composition | VEHICLE........98.0% - 99.0%, Acrylic latex.....31.5% - 32.0%, Volatiles.....68. |
| | | |
Properties
| | | | | |
| VOC gr/L | 223.00 | Volume Solids ±2% | 30.50 | Odor | Mild ammonia odor. |
| VOC lbs/G | 1.86 | Weight Solids ±2% | 33.25 | Thinning | None required. Clean tap water |
| |
| MPI # | | Theor. Spread Rate | 200.0 | Weight | 8.50 |
| Gloss 60° | 20-28 | Wet Film Thickness | 9 | Viscosity | 72 - 76 Kerbs Units at 77°F |
| Sheen 85° | | Dry Film Thickness | 2.9 | Resistance | |
| |
| Tinting Type | | Toxic Properties | None as a dry film. Use with a | Cleanup | warm soapy water |
| Local Harvest | | Light Reflectance | | Packaging | |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
at 77 F and 50% Relative Humidity
| | | | | |
| Dry To Touch | 1 1/2 hour | Dry To Sand | | Tack Free | |
| Dry To Recoat | 4 hours | Dry To Topcoat | | Dry To Hard | 7-14 days |
Prep & Prime
All surfaces to be painted must be clean and dry. CAUTION!! Material dries quickly in thin films and will form skins which may clog equipment. Keep container covered or mist water on the to prevent premature drying.
GALVANIZED: Allow to weather 6 months prior to Solvent Clean SSPC-SP1 & painting. If weathering is not possible. Solvent Clean per SSPC-SP1. apply test patch & allow to dry 1 week before testing adhesion.
PVC/FIBERGLASS: Scuff sand to abrade surface & Apply test patch, wait 1 week before testing adhesion.
| |
| Concrete Block | Apply 501901x Sprayable Block Filler and allow to thoroughly dry before topcoating. |
| Masonry | Must be thoroughly cured before painting. Priming with 501601x First Coat Primer is recommended prior to topcoating. |
| Metal | Suggest minimum preparation of Hand Tool Cleaning per SSPC-SP2. Remove all grease & oil per Solvent Cleaning SSPC-SP1. Remove chalk & old paint not tightly bonded to the surface. Clean all visible rust to bare metal. Smooth or shiny surfaces should be abraded to improve adhesion of the coating to the substrate. |
| |
| Wood | Priming wtih 501601x First Coat Primer is recommended prior to topcoating. |
| |
Application
Apply when substrate temperatures is 50 F. or above and expected to remain above 50 F for a minimum of 24 hours. Do not apply out doors if rain or dew is expected within 24 hours or completion.
| |
| Coats | Apply one or two coats to achieve 2.5 -3.5 milsdry film thickness. |
| |
| Roller / Pad | Use a top quality synthetic roller cover. |
| Airless Spray | Equipment capable of maintaining constant 1800 psi at the tip (.013" to .019" tip orifice) |
| |
| Conventional Spray | DeVilbiss JGA Gun or equivalent. Fluid pressure 25 - 30 psi ( pressure 40 - 50 psi) |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 4/12/2010 - Please contact us at 800.452.2315 for additional information or questions
