Anti Skid Epoxy Finish Light Gray
Product Data Sheet
| | | |
| Description | A Two Component, High Build, High Solids, Epoxy Non-Skid Coating Containing Aluminum Oxide aggregate. |
732507x
32391x Catalyst | |
|
| Basic Use | Recommended for use on steel decks, heli pads, ramps, walkways, and concrete floors where the ultimate in a non-skid surface is desired. This coating is resistant to chemicals, solvents, grease, oil, water, detergents, and hydraulic fluid. |
| |
| Pot Life | 1 to 2 hours | | |
| | Composition | VEHICLE........41.64%, Epoxy and Hardener Non-volatile......73.9%, Volatile..... |
| Induction | 15 minutes. | Mixing Instructions | Mix part A and part B together. Mix frequently during use. |
Properties
| | | | | |
| VOC gr/L | 189.00 | Volume Solids ±2% | 78.10 | Odor | aromatic paint thinner. |
| VOC lbs/G | 1.58 | Weight Solids ±2% | 89.14 | Thinning | None recommended. |
| |
| MPI # | | Theor. Spread Rate | 60.0 | Weight | 14.53 |
| Gloss 60° | 0 - 3 | Wet Film Thickness | N/A | Viscosity | 120 to 140 Kerbs Units. |
| Sheen 85° | N/A | Dry Film Thickness | N/A | Resistance | Excellent. |
| |
| Tinting Type | N/A | Toxic Properties | None as a dry film. | Cleanup | Use MEK |
| Local Harvest | | Light Reflectance | Less then 25. | Packaging | Stocked in single gallons |
| |
| | | | | |
| |
| | | | | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
Dry Times
Dry @ 24 hours; full cure in 7 days.
| | | | | |
| Dry To Touch | 4-6 hours | Dry To Sand | N/A | Tack Free | 6-8 hours |
| Dry To Recoat | 8 -12 hours | Dry To Topcoat | 8-12 hours | Dry To Hard | 24 hours |
Prep & Prime
| |
| |
| Masonry | Masonry surfaces must be clean and thoroughly cured prior to coating. Surface should not be smooth but rather the texture of medium sandpaper. To enhance adhesion an epoxy primer may be used under the non-skid. |
| Metal | Blast clean to SSPC SP6 Commercial Blast or SSPC-SP11 Power Rool Clean to bare metal. Prime with an appropriate metal primer for your substrate. |
| |
| Wood | Not recommended. |
| |
Application
| |
| |
| |
| Roller / Pad | The highest possible profile is achieved with a nylon loop roller cover or a core roller. A sand finish is achieved with a 3/8" nap roller cover. |
| |
| |
| |
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 11/11/2011 - Please contact us at 800.452.2315 for additional information or questions
