Anti Skid Epoxy Finish
Product Data Sheet
|
|
|
|
| Description |
|
|
|
|
|
| Basic Use |
A two component, high build, high solids, epoxy non-skid coating. Recommended for use on decks, heli pads, ramps, walkways, and concrete floors where the ultimate in a non-skid surface is desired. This coating is resistant to chemicals, solvents, grease, oil, water, detergents, and hydraulic fluid. |
|
|
| Pot Life |
1 to 2 hours |
|
|
|
|
Composition |
VEHICLE........41.64%, Epoxy and Hardener Non-volatile......73.9%, Volatile..... |
| Induction |
Fifteen minutes. Mix with a po |
Mixing Instructions |
Mix part A and part B together. Allow material to "sweat in" for 15 minutes at 7 |
Properties
|
|
|
|
|
|
| VOC gr/L |
69.00 |
Volume Solids ±2% |
78.10 |
Odor |
Dominant odor of a paint thinn |
| VOC lbs/G |
0.58 |
Weight Solids ±2% |
89.14 |
Thinning |
None recommended. |
| |
| MPI # |
|
Spread Rate |
0.0 |
Weight |
14.53 |
| Gloss 60° |
|
Wet Film Thickness |
|
Viscosity |
120 to 140 Krebs Units (very t |
| Sheen 85° |
|
Dry Film Thickness |
|
Resistance |
Excellent |
| |
| Tinting Type |
|
Toxic Properties |
Non-toxic as a dry film. |
Cleanup |
Use MIBK or Ropon Epoxy Thinne |
| Local Harvest |
|
Light Reflectance |
Less then 25. |
Packaging |
Stocked in single gallon conta |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
| |
|
|
Dry Times
At 77° Fahrenheit and 50% Relative Humidity:
|
|
|
|
|
|
| Dry To Touch |
|
Dry To Sand |
|
Tack Free |
|
| Dry To Recoat |
|
Dry To Topcoat |
|
Dry To Hard |
24 hours, full cure in 7 days |
Prep & Prime
|
|
|
|
| Masonry |
Surfaces must be clean and thoroughly cured prior to coating. Surface should not be smooth but rather texture of medium sandpaper. To enhance adhesion an epoxy primer may be used under the skid coat. |
| Metal |
Blast clean to SSPC 10. Prime with Ropon Epoxy Red Oxide Primer. |
|
|
| Wood |
Not recommended for wooden surfaces. |
|
|
Application
|
|
|
|
|
|
| Roller / Pad |
The highest possible profile is achieved with a nylon loop rollercover or a core roller |
|
|
|
|
|
|
Corporate: 6107 N Marine Drive Portland, Oregon 97203 - Rodda Paint Co. - Regional: 3838 4th Avenue South Seattle, Washington 98134
Disclaimer - All technical advice, recommendations and services regarding this product are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable and are intended for use by persons having skill and know-how, at their discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from this product use by Buyer whether as recommended herein or otherwise. Such recommendations, technical advice or services are not to be taken as a license to operate under or suggest infringement of any patent.
Last Modification Date: 3/25/2009 - Please contact us at 800.452.2315 for additional information or questions
