Material Safety Data Sheet

Last Update: 11/06/12
health
flammability
reactivity
personal protection

LACQUER THINNER

799461
Manufacturer: RODDA PAINT COMPANY6123 N MARINE DRIVEPORTLAND, OR 97203
Name of preparer: Rick BarnardInformation Phone: (503) 521-4300
Emergency Phone: (800) 424-9300

Hazardous Ingredients / SARA III Information

Reportable ComponentsCAS NumberVapor Pressure
mm Hg @ Temp
Weight
Percent
VM&P NAPHTHA8032-32-45.025C30 - 40
OSHA TLV- 300ppm STEL- 400ppm
NIOSH TWA- 350mg/m3 Ceiling- 1800mg/m3 (value based on 15 minutes)
ACGIH TWA- 300ppm 1370mg/m3
ETHANOL64-17-510 - 20
ACGIH: TLV(1000PPM) OSHA: PEL(1000PPM)
METHYL ETHYL KETONE78-93-370.920C10 - 20
OSHA TWA- 200ppm 590mg/m3
NIOSH TWA- 200ppm 590mg/m3 STEL- 300ppm 885mg/m3
ACGIH TWA- 200ppm 590mg/m3 STEL- 300ppm 885mg/m3
*># TOLUENE108-88-32268F10 - 20
OSHA TWA- 200ppm Ceiling- 300ppm (OHSA PEL Table Z-2: Acceptable maximum
peak above the acceptable ceiling concentraction for an 8-hour shift:
500ppm/10 minutes)
NIOSH TWA- 100ppm 375mg/m3 STEL- 150ppm 560mg/m3
ACGIH TWA- 50ppm 188mg/m3
*# XYLENE1330-20-75.120 C0 - 10
OSHA TWA- 100ppm 435mg/m3
NIOSH TWA- 100ppm 435mg/m3 STEL- 150ppm 655mg/m3
ACGIH TWA- 100ppm 434mg/m3 STEL- 150ppm 651mg/m3
>* GLYCOL ETHER111-76-20.8825C0 - 10
OSHA TWA- 50ppm 240mg/m3
NIOSH TWA- 5ppm 24mg/m3
ACGIH TWA- 25ppm 121mg/m3
*# METHANOL67-56-197.6820C0 - 10
OSHA TWA- 200ppm 260mg/m3
NIOSH TWA- 200ppm 260mg/m3 STEL- 250ppm 325mg/m3
ACGIH TWA- 200ppm 262mg/m3 STEL- 250ppm 328mg/m3
ACETONE67-64-1181.720C0 - 10
OSHA TWA- 1000ppm 2400mg/m3
NIOSH TWA- 250ppm 590mg/m3
ACGIH TWA- 500ppm 1188mg/m3 STEL- 750ppm 1782mg/m3
ISOPROPANOL67-63-03220C0 - 10
OSHA TWA- 400ppm 980mg/m3
NIOSH TWA- 400ppm 980mg/m3 STEL- 500ppm 1225mg/m3
ACHIG TWA- 400ppm 983mg/m3 STEL- 500ppm 1230mg/m3
+*#> ETHYLBENZENE100-41-41020 C0 - 10
OSHA TWA- 100ppm 435mg/m3
NIOSH TWA- 100ppm 435mg/m3 STEL- 125ppm 545mg/m3
ACGIH TWA- 100ppm 434mg/m3 STEL- 125ppm 543mg/m3
The above chemical(s) meet the criteria as defined under 29 CFR 1910 for toxic and hazardous substances. * Indicates toxic material(s) subject to the reporting requirements of Section 313 of Title III and of 40 CFR 372. + Indictates material(s) listed as a NTP, IARC, or OSHA carcinogen.>Indicates material(s) listed on California's Proposition 65 known to the state to cause reproductive toxicity or cancer. # Indicates materials listed in Section 112(b) of the Clean Air Act.

Physical / Chemical Characteristics

Boiling Range: 133F - 336F
Vapor Density: Heavier than air.
Solubility in Water: None
Appearance and Odor: Clear liquid, strong solvent odor.
Coating VOC: 6.73 lb/gl
Material VOC: 6.46 lb/gl
Specific Gravity: 0.81
Evaporation Rate: Slower than Butyl Acetate.

Fire and Explosion Hazard Data

Flash Point: -1.0F
Method Used: TCC
Flashable limits in air by volumeUpper: 19.0Lower: 0.9
Extinguishing Media: CO2, dry chemical, foam, or water fog.Special Firefighting Procedures:For fires involving this material, do not enter any enclosed or confined fire space without proper protective equipment. Self-contained breathing apparatus with a full facepiece operated in pressure-demand or other positive pressure mode to protect against the hazardous effects of normal products of combustion or oxygen deficiency. Unusual Fire and Explosion Hazards:Vapors are heavier than air and may travel along the ground or be moved by ventilation and ignited by heat, pilot lights, other flames and ignition sources at locations distant from material handling point. Never use welding or cutting torch on or near drum (even empty) because product (just residue) can ignite EXPLOSIVELY! Thermal decomposition of this product will produce carbon monoxide and carbon dioxide.

Reactivity Data

Stability: Stable
Hazardous Polymerization: Will not occur
Conditions to Avoid:Excessive temperatures, poor ventilation, and corrosive atmospheres. Avoid all heat sparks and sources of ignition. Incompatibility (Materials to Avoid):Strong oxidizing agents, strong alkalies, heat.Hazardous Decomposition or Byproducts:Normal combustion forms carbon dioxide and water vapor; incomplete combustion can produce carbon monoxide.

Health Hazard Data

Inhalation - Health Risks and Symptoms of Exposure:Use only with adequate ventilation. Do not breathe dust or spray mist. Ensure fresh air entry during application and drying. For spray application, sanding, abrading, and dust cleanup, wear an appropriate properly fitted respirator (NIOSH/MSHA TC21C approved). Follow respirator manufacturer's directions for respirator use. Excessive inhalation of vapors can cause nasal and respiratiory irritation. If affected, remove to fresh air. If breathing is difficult, administer oxygen. If breathing has stopped, give artificial respiration. Get medical attention. Skin and Eye Contact - Health Risks and Symptoms of Exposure:Exposure may cause mild to moderate skin irritation. Symptoms of exposure may include: drying and cracking of the skin, redness and a buring senstation. Exposure may cause severe eye irritaion. Symptoms of exposure may include: tearing, redness and a stinging sensation. Skin Absorbtion - Health Risks and Symptoms of Exposure:Prolonged exposure limit may result in the absorption of harmful amounts of material. Ingestion - Health Risks and Symptoms of Exposure:Toxicity is low. Symptoms may include: central nervous system depression, dizziness, drowsiness, weakness, fatigue, nausea, headache, unconsciousness, kidney damage. Health Hazards (Acute and Chronic):Potential local and systemic effects due to single or short term overexposure to the eyes and skin or through inhalation or ingestion. Health Hazards of Previous Coatings:WARNING! If you scrape, sand, or remove old paint, you may release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO AVIOD EXPOSURE. Wear a NIOSH-approved respirator to control lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you start, find out how to protect yourself and your family by contacting the National Lead Information hotline at 1-800-424-LEAD or log on to www.epa.gov/lead. Carcinogenicity:NTP Carcinogen:NoIARC Monographs:YesOSHA Regulated:Yes
This material is not listed as a human carcinogenic.Medical Conditions Generally Aggrevated by Exposure: Overexposure of this mataerial has been suggested as a cause of the following effects in humans, and may aggravate pre-existing disorders of these organs: testis damage, male and female reproductive fertility effects. Emergency and First Aid Procedures:SKIN- Wash exposed area with soap and water. EYES- Flush with large amounts of water.

Precautions for Safe Handling and Use

Steps to be Taken in Case Material is Released or Spilled:Eliminate all ignition sources (flares, flames including pilot lights and electrical sparks). Persons not wearing protective equipment should be excluded from area of spill until clean-up had been completed. Stop spill at source, dike area of spill to prevent spreading, pump liquid to salvage tank. Remaining liquid may be taken up with sand, clay, earth, floor absorbent, or other absorbent material and shoveled into containers. Prevent run-off sewers, streams, or other bodies of water. Waste Disposal Method:Destroy by liquid incineration. Material collected on absorbent material may be deposited in an approved landfill in accordance with local, state, and federal regulations. Precautions to be Taken in Handling and Storing:Store in a cool, dry area. Keep away from heat, sparks, and open flame. Keep containers closed when not in use. Use only with adequate ventilation. Other Precautions:Warning!!! Sudden release of hot organic chemical vapors or mists from process equipment operating at elevated temperatrues and pressure, or suddent ingress of air into equipment, may result in ignitions without the presence of obvious ignition sources. Any use of this product in elevated temperature processes should be thoroughly evaluated to establish and maintain safe operating conditions.

Control Measures

Respiratory Protection:If TLV of the product or any component is exceeded, a NIOSH/MESA jointly approved self-contained breathing apparatus with a full face piece operated in pressure demand or other positive pressure mode is advised; however, OSHA regulations also permit other NIOSH/MESA respirators under specified conditions. (See your safety equipment supplier). Ventilation:Provide sufficient mechanical and/or local exhaust to maintain exposure below TLV(s). Protective Gloves:Wear resistant gloves such as: BUNA-NEye Protection:Chemical splash goggles in compliance with OSHA regulations are advised, unless full facepiece respirator is worn. Other Protective Clothing or Equipment:N/AWork / Hygienic Practices:Wash hands thoroughly after handling this product.

Disclaimer

This information provided as a resource only. It should not be taken as a warranty or representation for which Rodda Paint Co. assumes legal responsibility. The information contained is believed to be accurate and compiled from sources believed to be reliable, it is the responsibility of the user to investigate and verify its validity. The user assumes all responsibility of using and handling the product in accordance with applicable federal, state, and local regulations.

How can we help you today?